Energy Storage Spot Welder

Energy Storage Spot Welder

Details
The HFTR-10000 is a pneumatic energy storage spot welder for localized spot and projection welding of formed metal parts, brackets and selected electrical contact assemblies. Its capacitor bank stores energy before each weld and releases it through the electrodes during a short cycle. Final suitability is confirmed by sample testing.
Category
Capacitor Discharge Welding Machine
 
Add To Inquiry
Send Inquiry
Description
Technical Parameters

The HFTR-10000 is a stationary press-type resistance welding machine. It is designed for manufacturers that need to produce localized spot or projection joints on small and medium formed metal components.

Typical workpieces include stamped brackets, mounting plates, electrical contact supports, stainless-steel components, galvanized hardware and parts with controlled welding projections.

Before each weld, electrical energy is stored in the capacitor bank. After the electrodes close and the required force is established, the stored energy is released through the transformer, secondary circuit and electrodes. Electrical resistance at the joint generates heat and forms the weld.

 

HFTR-10000 Product Analysis    HFTR-10000 Welding sample display

 

HFTR-10000 Technical Specifications

 

Parameter Unit HFTR-10000
Product Type - Capacitor energy storage spot and projection welder
Capacitance µF 20,000
Input Capacity kVA 15
Rated Power Supply V / Hz 380 / 50
Rated Duty Cycle % 50
Maximum Primary Current A 60
Primary Cable Specification mm² 3 × 10 + 2 × 6
Maximum Short-Circuit Current kA 38
Secondary Voltage V 12–14
Pneumatic Cylinder mm Ø160 × 110
Maximum Electrode Force kN 10
Operating Temperature °C 1–45
Relative Humidity % 35–90
Welding Process - Resistance spot and projection welding
Installation Type - Stationary press-type machine

 

Equipment Advantages

 

 

High Efficiency

Equipped with high-load metal film capacitors, meeting the demands of multi-shift production.

 

Precise Control

Microcomputer control system ensures precise control of welding time and discharge process.

 

Energy saving

No need for water cooling, with energy consumption reduced by over 50% compared to traditional AC welding equipment.

 

High Stability

Stable welding performance, especially suitable for high-strength steel and hot-formed steel welding.

Process Characteristics

 

Localized Energy Delivery

The capacitor bank stores energy before the weld rather than drawing the full welding current directly from the power supply during the welding event.

Energy is released through the welding circuit at the selected joint. The actual current through the workpiece depends on secondary-circuit impedance, electrode contact and workpiece resistance.

 

01

Short Welding Cycle

The welding current is delivered during a short cycle. This can help limit heat spread around the joint when the welding conditions and contact geometry are correctly matched.

Short welding time does not automatically guarantee sufficient strength or eliminate every surface mark. The result must be verified on actual samples.

02

Pneumatic Electrode Force

The pneumatic cylinder applies force before and during energy release. Electrode force influences contact resistance, heat generation, projection collapse and molten-metal containment.

Insufficient force can cause unstable contact or spatter. Excessive force can flatten the projection too early and reduce the resistance needed to generate heat.

03

Adjustable Process for Different Joints

The welding condition can be developed around the material, thickness, joint geometry and strength requirement.

A new material, coating or projection design should be treated as a new welding application until it has been tested.

04

Fixture and Electrode Configuration

Electrodes and workpiece fixtures are designed around the customer's part. Correct tooling helps control part location, electrode access and the welding-current path.

Where required, the fixture can be evaluated for part-presence detection, mistake prevention or integration with a simple loading system.

05

 

Materials: Carbon steel, stainless steel, copper, silver, nickel, and alloys.

 

 

Materials

 

Typical Applications

 

 

Formed Sheet-Metal Brackets

The HFTR-10000 can be evaluated for mounting brackets, support plates, clips and stamped sheet-metal components.

The fixture should locate the workpiece from stable reference points and prevent movement during electrode closure.

Stainless-Steel Attachments

Possible applications include small stainless-steel supports, mounting pieces and attachments used in appliances, enclosures and industrial products.Surface marking, indentation and discoloration should be included in the acceptance criteria where the welded surface remains visible.

Galvanized Hardware Components

The machine can be evaluated for selected galvanized brackets, clips, fittings and components with controlled welding projections.

The coating can affect contact resistance and electrode wear. Production material should therefore be used during sample testing.

Electrical Contact Assemblies

Selected copper, nickel or silver contact materials can be welded to suitable support components after process testing.

The review should consider conductivity, contact position, joint area, electrode material and required electrical or mechanical performance.

Electromechanical Components

Potential applications include selected terminals, supports, mounting plates and small formed components used in motors, switches and other electromechanical products.

Nearby insulation, finished surfaces and functional areas must be considered when the electrode and fixture are designed.

Small Projection-Welded Fasteners

Small weld nuts, pins or fasteners can be evaluated when the total projection area and required force fall within the machine's verified range.

This page does not target large automotive nuts, large ring projections or simultaneous multi-fastener welding. Those applications may require a higher-capacity or dedicated nut projection welding machine.

 

FAQ

 

 

Capacitor energy storage projection welding on an automotive sheet metal component

01.What is an energy storage spot welder?

An energy storage spot welder stores electrical energy in a capacitor bank before each weld. The stored energy is released through the transformer and electrodes to form a localized resistance spot or projection weld.

02.What is the HFTR-10000 used for?

The HFTR-10000 is intended for localized welding of formed metal parts, brackets, attachments, selected electrical contacts and small projection joints.

Suitability depends on material, thickness, joint area, electrode access and required strength.

03.Is this a portable battery spot welder?

No. The HFTR-10000 is a stationary industrial press-type welding machine.

It is not a handheld or portable welder for 18650 battery cells.

04.Can it weld stainless steel?

Selected stainless-steel spot and projection joints can be evaluated.

Surface appearance, indentation, discoloration, material thickness and required strength should be included in the sample approval.

05.Can it weld copper, nickel or silver contacts?

Selected contact joints can be tested. The result depends on the conductivity, contact area, support material, electrode design and required electrical or mechanical performance.

06.Can the HFTR-10000 weld large automotive nuts?

It may be suitable for selected small fasteners, but large nuts, large ring projections or several simultaneous projections may require a higher-capacity machine.

Send the fastener drawing and base-part information for evaluation.

 

 

Wuxi Haifei Intelligent Equipment Co., Limited is one of the leading manufacturers and suppliers of energy storage spot welder in China. With abundant experience, we warmly welcome you to buy advanced energy storage spot welder for sale here from our factory. Quality products and reasonable price are available.

 

Hot Tags: energy storage spot welder, China energy storage spot welder manufacturers, capacitor energy storage welder, Capacitor Discharge Spot Welder For Three Way Catalytic Converters

Send Inquiry

Start Your Welding Machine Project with Haifei

Share your workpiece drawing, material, welding position, required output, and quality requirements. Haifei will review your welding process and recommend a suitable busbar welder, resistance welder, or customized automation solution.

Contact Our Engineer