In the rapidly expanding fields of new energy vehicle battery modules, photovoltaic energy storage systems, and ultra-high voltage power transmission, Polymer Diffusion Welding (often referred to simply as Diffusion Welding in this context) has become a critical technology for achieving molecular-level bonding in copper and aluminum foil flexible busbars. This process utilizes high temperature and pressure to promote atomic inter-diffusion, forming joints with extremely low electrical resistance and high mechanical strength.




However, "Lack of Fusion" (LOF)-where the weld interface is insufficiently bonded-is a common technical bottleneck for many manufacturers. This defect not only increases the resistance and heat generation in the connector but can also lead to failure under vibration, potentially causing severe power system accidents. This article provides an in-depth analysis of the causes of LOF and offers quantified, practical optimization strategies.
In-Depth Analysis: Why Does Your Diffusion Weld Suffer from "Lack of Fusion"?
The essence of diffusion welding relies on thermal energy and mechanical pressure to bring the two surfaces within atomic attraction range. Lack of Fusion typically occurs when the "energy input" or "physical contact" during the welding process fails to meet the critical threshold.
1. Energy Input Imbalance: The "Weakest Link" of Temperature and Time
Welding temperature is the primary driver for atomic diffusion. Generally, the diffusion welding temperature must be set between 0.5 and 0.8 times the absolute melting point ($T_m$) of the base material (in Kelvin). If the temperature is set too low, the atomic kinetic energy is insufficient to overcome the interfacial energy barrier.
Furthermore, thermal conduction lag is a major cause of LOF in thick workpieces. For instance, when welding a thick busbar composed of 100 layers of 0.1mm copper foil, if the welding time is too short, heat may only penetrate the outer layers. This results in the core region failing to reach the required temperature, a classic "overcooked outside, undercooked inside" scenario.
2. Physical Barriers: The Invisible Walls of Oxide Films and Machining Precision
While diffusion welding in an air environment, using its unique heating method, suppresses severe oxidation, the existing oxide films on the material surface (such as $Al_2O_3$ on aluminum foil) have extremely high melting points. If the pressure is insufficient to crush this film at high temperatures, it acts as an insulating barrier, preventing molecular interpenetration. Simultaneously, if the flatness of the surfaces to be welded is poor (roughness exceeding 0.1mm), the actual contact area will be significantly smaller than the nominal area, leading to microscopic voids in non-contact regions.
Practical Solutions: A Five-Step Optimization Method to Eliminate Welding Defects
To address the LOF issue, companies should not rely on blindly increasing parameters but rather establish a scientific, closed-loop optimization system.
1. Precise Temperature Control: Establishing a Material-Specific "Temperature Matrix"
Different materials have vastly different temperature sensitivities. When adjusting the diffusion welder, it is recommended to follow these quantified standards for phased optimization:
| Application Scenario | Recommended Temp. Range ($^\circ$C) | Pressure Range (MPa) | Key Process Logic |
| Aluminum Foil Flex Busbar (0.1mm x 50 layers) | 480 - 540 | 5 - 8 | Focus on rapid temperature rise to minimize oxidation. |
| Copper Foil Flex Busbar (0.1mm x 100 layers) | 550 - 620 | 10 - 15 | Requires a preheating stage to ensure core penetration. |
| Copper-Aluminum Dissimilar Joining | 500 - 580 | 8 - 12 | Strictly control time to prevent the formation of brittle intermetallic compounds. |
2. Pressure Management: The Physical Prerequisite for Molecular Contact
Pressure is not only used to clamp the workpieces but, more importantly, to induce microscopic plastic deformation, ensuring intimate contact between the surfaces. If localized LOF occurs, the parallelism of the dies (molds) should be checked. It is recommended to use pressure-sensitive film to test the pressure distribution, ensuring that the full-plane pressure fluctuation is controlled within $\pm 10%$. Increasing the pressure to 12-15 MPa can significantly improve LOF caused by insufficient surface flatness, but care must be taken to prevent excessive extrusion deformation at the edges of the workpiece.
3. Surface Purification: Deep Cleaning Processes Beyond Simple Wiping
For high-demand energy storage busbars, simple alcohol wiping may be insufficient to remove deep-seated oil and grease. It is recommended to introduce acid pickling or plasma cleaning processes to remove oxide layers with a thickness exceeding 10nm. Experimental data shows that workpieces subjected to deep cleaning can achieve a shear strength increase of over 20% under the same welding parameters.
Targeted Case Studies: Differentiated Applications in the New Energy and Power Industries
1. Aluminum Foil Flex Busbars for EV Batteries: Low-Pressure, Fast-Weld Strategy
In EV battery modules, aluminum foil is highly susceptible to oxidation and has a low melting point. The key to resolving LOF is speed. By increasing the power response speed of the welder, the diffusion process is completed before the oxide film thickens significantly. A strategy of lower pressure (5-7 MPa) combined with an extremely short time (5-15 seconds) is typically employed.
2. High-Voltage Power Copper Busbars: High-Pressure, Constant-Temperature Strategy
Power busbars are thick and dissipate heat quickly. The key to resolving LOF is penetration. A two-stage heating mode is recommended: first, preheat at a lower power to $300^\circ$C and hold for 20 seconds to minimize the internal/external temperature difference. Then, rapidly ramp up to the welding temperature, coupled with a high pressure of 15 MPa during the hold time, to ensure complete fusion of every copper foil layer.
Purchasing and Selection Advice: How to Choose a Reliable Diffusion Welding Machine
When selecting or purchasing a diffusion welding machine, users should focus on the following technical indicators to mitigate the risk of LOF from a hardware perspective:
- Closed-Loop Monitoring of the Control System: Does the equipment feature real-time pressure-displacement monitoring? The ability to record the real-time compression amount during welding is a crucial indicator for assessing weld penetration.
- Heating Uniformity: Inquire about the temperature distribution of the induction coil or resistance heating plate. A high-quality machine should ensure the temperature difference across the working surface is within $\pm 5^\circ$C.
- Non-Vacuum Anti-Oxidation Technology: Investigate whether the equipment offers localized inert gas protection or specialized pressurized anti-oxidation structures. This is vital for solving LOF issues in aluminum alloy welding within an air environment.
Conclusion
Resolving the Lack of Fusion in diffusion welding is essentially a matter of precisely balancing temperature, pressure, time, and surface quality. By establishing a material-specific temperature matrix, optimizing die parallelism, and implementing deep surface purification, companies can effectively eliminate welding hazards and enhance the competitiveness of their products in the new energy and power markets. When selecting equipment, prioritize models with data monitoring and high-precision temperature control capabilities, as this will lay a solid foundation for your future automated production.

